Knowledge Saves Time and Money

 •Knowledge of marine corrosion CAUSE will save you a fortune:

 Link to Home page and Menu

 You do not need to remember this course. Add a link to your Browser (Ctrl plus d) then use it as a reference

  Audio - How to eliminate corrosion CAUSE.
 To listen click here

   •It is much cheaper to stop the stray current that causes marine corrosion now: purchase SeaBis System

 •SeaBis is a complete system to stop the CAUSE of stray current creating marine corrosion.

 •No Blocker required. We do not use a Blocker, we eliminate the CAUSE.

 Index:

•Explanation - the original cause of electrolysis:

•Causes - not true

•Understand the real cause then eliminate it

•Is there DC in AC (shore power / inverter)?

•SeaBis guarantee

•What is SeaBis?

•Benefits of SeaBis

•Use of multi meter / 1/2 cell must fail

•ABYC Wiring Rules

•Why buy a Blocker?

•Why do small aircraft get electrolysis

•Electrolysis elimination 97% calculation

•Why do small to medium trucks get electrolysis?

 •Explanation - the original cause of electrolysis:

 The cause of corrosive current is the battery ”0” volts terminal. In Kelvin Absolute Law terms (see Wikipedia) is actually at minus 12 volts for a 12 volt battery (24 for 24 volt battery). The metal contains electrons which are negatively charged. So the two negatives repel each other causing electrolysis to dissolve your metal into particles. The Earth is at +1.2 volts so attracts those particles. So your metal corrodes to the Earth. The solution is to use SeaBis to eliminate the cause.
See: Wikipedia electrolysis. Note DC (battery) power – the Apparatus power leads are red and black, and first paragraph specifically states DC, not AC(mains or shore power).

 

 Causes - not true:

 AC - Mains / shore / inverter power. AC current (power) cannot cause electrolysis as it changes direction every half cycle / Hertz.

 So IF it takes off a metal particle in the first half cycle it will replace it in the second half cycle.

 AC cannot cause electrolysis - it is impossible.


 Understand the real cause then eliminate it.

 DC (battery) current flows in the same direction, permanently.

 So will continually dissolve your metal. 24 hours every day of the year. With the negative only connected it will conduct to the Earth.

 Eliminate the CAUSE by using SeaBis Master and booklet supplied with SeaBis: How To Stop Corrosion.


 Is there DC - direct or battery current in AC?

 Please read the specification on your electric kettle / pot / hotplate. There will be no DC entry.

 If there were DC in the AC the electric kettle / pot / hotplate would attempt to draw in infinite current and burn out in a few seconds. As would every appliance in your country.

 Reference Wikipedia:- DC does not create Back EMF (Counter-electromotive force) so there is no resistance to DC current flow. DC current would attempt infinity.


 We must be correct: We guarantee to eliminate ALL CAUSES of electrolysis for 8 years using enclosed booklet: How To Stop Corrosion

 How to stop corrosion: the reason we supply a 8 year money back guarantee is we are 100% correct. Current through damp to wet metal to Earth is eliminated, permanently.

 That means no electrolysis, permanently.


 What is SeaBis?

 SeaBis is an electronic device with How To Stop Corrosion that WILL 100% and permanently stop electrolysis:

 Use the SeaBis System to identify then eliminate the leaking stray electrical current that is the direct cause.

 Permanently. No hull / metal penetration / additional coating or plating. The stray current SOURCE is eliminated.


 The benefits of using SeaBis - Use How To Stop Corrosion to eliminate the CAUSE.

 SeaBis shows the invisible electrolysis current that will cause corrosion in real time.

 There is no need to slip the vessel to see the anodes eaten away because SeaBis will be showing a warning light instantaneously.

 Better yet the SeaBis units Normal - green light is lit continuously with absolute peace of mind that the vessel is free of the stray current that will cause corrosion.

 How to stop corrosion completes elimination of ALL CAUSES.


 Stray current causes electrolysis that is the cause of 97% of all corrosion.

 Electrolysis is caused by DC (battery) current ONLY. The MAIN source of stray current that causes electrolysis is the vessels' own battery bank. ALL CAUSES are eliminated by SeaBis System. 

 Stop electrolysis then rust and galvanic corrosion are easy to eliminate. The paint, coatings and anodes will not be destroyed by electrolysis.

 Your engine and hull will not be dissolved and anodes can protect your metal from galvanic corrosion as designed.

 SeaBis may be used with battery clips and moved battery bank to battery bank to eliminate all permanent causes. Intermittent and new causes require SeaBis be permanently installed.


 •Why does SeaBis succeed when a multi meter / test bulb-lamp / 1/2 cell must fail?

 The technical reason:

 Measurements must be used with everything at full power and at applied voltage (12 or 24 volts) without a limit in the measuring device and an extremely high current sensitivity. That device must have no effect on the circuit to be measured. SeaBis Master complies. Multi-meters measure at 1 volt at 1 millionth of an amp so have a error probability of greater than 1,000:1. In addition they alter the circuit under test. So multi-meters do not comply.

 Using a multimeter on amps is worse and has resulted in death from acid burns caused by the multi meter shorting the battery and it exploding, on fire, hydrochloric acid over you.

 Test lamps are one million times insensitive. 1/2 cell, as a multimeter or test lamp measures voltage so can only deceive you.

  Stray current causes electrolysis. That is why I developed SeaBis. SeaBis measures current, accurately and safely. It separates the various types and levels of current so you know if your vessel is safe from electrolysis. SeaBis indicates the degree of risk so you can time your repair and if excessive AC in your DC can damage your batteries or electronics. How To Stop Corrosion completes the elimination of ALL causes. Permanently.

 In doubt? Ask any manufacturing jeweler how he plates gold onto base ring. The gold is your damp too wet marine engine / hull and the base (jewelry-ring) is the Earth.

 Contact us: E-mail Glen Bishop or phone +61 for Australia then (0)417 878 773 or Skype: seabis1. All free.


ABYC Wiring Rules

 There are various versions of ABYC in circulation. This link: will download mine. They are genuine. Judge for yourself.
 May down load to folder Downloads.


 Why buy a Blocker?

 Some will try confusion by calling Blocker a Galvanic Isolator!
 Don't be deceived.

  Ask for their WRITTEN guarantee. Ensure it has value - issued by a person with property in your country.

 SeaBis WRITTEN 8 year money back Guarantee is here - written guarantee


 Why do small to medium aircraft get electrolysis?

 Clouds have greater than 10% humidity. The air around aircraft, in clouds, contains more than the tolerance level of 10% humidity.
 Any metal in contact with the Earth, even remotely thru the air, passes stray current to the Earth so causing electrolysis.

 Large aircraft are correctly insulated so do not get electrolysis.

 How to stop corrosion completes elimination of ALL CAUSES.


 Stray current causes electrolysis that is the cause of 98% of all corrosion.

 Electrolysis is caused by DC (battery) current ONLY. The MAIN source of stray current that causes electrolysis is the vessels' own battery bank. ALL CAUSES are eliminated by SeaBis System. 

 Stop electrolysis then rust and galvanic corrosion are easy to eliminate. The paint, coatings and anodes will not be destroyed by electrolysis.

 Your engine and hull will not be dissolved and anodes can protect your metal from galvanic corrosion as designed.

 SeaBis may be used with battery clips and moved battery bank to battery bank to eliminate all permanent causes. Intermittent and new causes require SeaBis be permanently installed.


  Electrolysis elimination 97% calculation: Non commercial vessels use their engine/s less than 200 hours per year.

 There are 8,400 hours in a year so 200 hours divided 8,400 equals 2.38 percent of corrosion cause remaining, or contact me: contact@seabis.com.

 When SeaBis indicates NORMAL on all battery banks excluding engine we can supply a modified solenoid to keep engine electrolysis below 3%.
 In commercial use the engine ON hours will exceed 200 per year so full elimination of all causes is essential. We will guide you through, no matter the use.


 Why do small to medium trucks, planes and some vessels suffer from electrolysis when the larger do not?

 Larger trucks and planes are correctly insulated. That will be the result of SeaBis and How to Stop Corrosion.

 

 Free 30 minutes diagnostic support, value $80.00 and we will guide you thru how to stop corrosion. SeaBis products

 References click: Wikipedia - electrolysis
and Testimonials with verification
and Is electrolysis eating your boat.pdf maybe in your Downloads folder
and SeaBis System 100% works - Corrosionpedia.pdf maybe in your Downloads folder

 E-mail Glen Bishop: contact@seabis.com
 Skype name: seabis1. Download Skype - World-wide free PC to PC
 Australia (61) (0)417 878 773

 Link to Home page and Menu

 Copyright © 2018 Glen Bishop of SeaBis. All rights reserved.